AMAZON

Sunday, March 22, 2009

POST BEEP CODES

Post Beep Codes, AMI & Phoenix/Award BIOS error codes








Building a new PC or installing new hardware is fairly straight forward until things go wrong.

This page is © Copyright 2001-2008 helpwithpcs.com

Before you follow this tutorial you must read the terms of our disclaimer.

When a PC is first switched on or reset it performs a special diagnostic test called a POST (Power-On Self Test), to check all of the components in the PC the POST program sends out a signal to each device initialising each device's built-in self test procedure.
The POST test is a two stage process, first it will check all of the basic components including amongst other things the system clock, the processor, RAM, the keyboard controller and the Video Card.

When a device fails the first part of the POST, the BIOS will send a series of beeps from the PC's speaker (internal) to inform the PC user that there is a problem, these beeps are coded allowing the user to diagnose the troublesome component.

After the video has been tested the BIOS will then indicate any errors encountered by displaying either a numeric code or a text message on the screen.

When the POST has been completed successfully the PC will make a short beep to let the user know everything is as it should be.

back to top | © Copyright 2001-2008 helpwithpcs.com

Below are some common beep codes for AMI and Phoenix BIOS.


AMI BIOS ERROR BEEP CODES
1 Beep - Memory Refresh Failure (check memory)
2 Beeps - Memory Parity Error in first 64KB block (check memory)
3 Beeps - Memory Read/Write Error in first 64KB block (check memory)
4 Beeps - Motherboard timer not functioning (possible motherboard replacement)
5 Beeps - Processor Error (may need replacement Processor)
6 Beeps - Gate A20/keyboard controller failure (possible motherboard replacement)
7 Beeps - Processor Exception Interrupt Error (may need replacement Processor)
8 Beeps - Display Memory Read/Write Failure (reseat or replace video card)
9 Beeps - ROM checksum Error (replace BIOS chip or motherboard)
10 Beeps - CMOS shutdown Read/Write error (possible motherboard replacement)
11 Beeps - Bad Cache Memory - test failed (replace cache memory)

back to top | © Copyright 2001-2008 helpwithpcs.com

Phoenix BIOS ERROR BEEP CODES

Phoenix BIOS beep codes are a series of beeps separated by a pause, for example:
beep --- beep beep --- beep --- beep beep would be 1-2-1-2
1-1-4-1 - Cache Error (level 2)
1-2-2-3 - BIOS ROM Checksum
1-3-1-1 - DRAM Refresh Test
1-3-1-3 - Keyboard controller test
1-3-4-1 - RAM Failure on address line xxxx (check memory)
1-3-4-3 - RAM Failure on data bits xxxx of low byte of memory bus
1-4-1-1 - RAM Failure on data bits xxxx of high byte of memory bus
2-1-2-3 - ROM copyright notice
2-2-3-1 - Test for unexpected interrupts

back to top | © Copyright 2001-2008 helpwithpcs.com

AWARD BIOS ERROR BEEP CODES

There are 2 main beep codes for the Award BIOS:
one long beep and two short beeps - Video error (reseat or replace video card)
two short beeps - Non-Fatal Error (reseat RAM, check other components)

back to top | © Copyright 2001-2008 helpwithpcs.com
For more on BIOS beep codes or numeric codes see the manufacturer's website:
AMI BIOS
Phoenix/Award BIOS

back to top | Back to PC Upgrade Menu | © Copyright 2001-2008 helpwithpcs.com lintasberita

Voice chat in YM

Yahoo! (r) Messenger Tutorial Part 4 - Voice Conferencing

--------------------------------------------------------------------------------
note: This tutorial is currently being updated
--------------------------------------------------------------------------------
Voice conferencing can be a very handy feature of any instant messenger program, in this part we will look at how to use this feature in Yahoo!® Messenger.
--------------------------------------------------------------------------------
This page is © Copyright 2001-2008 helpwithpcs.com

Before you follow this tutorial you must read the terms of our disclaimer.
--------------------------------------------------------------------------------
If you use a dial-up connection then the chances are that the number you dial to connect to the internet is a local call (or included in a monthly fee such as broadband), this means that if you use the voice conferencing feature of a program like Yahoo!® Messenger instead of the phone it can save money with any long distance calls.
--------------------------------------------------------------------------------

In part four:
Setting up your mic & sound.
The Voice conferencing Toolbar.
Setting up the sound levels.
Back to course menu.



--------------------------------------------------------------------------------
Setting up your mic & sound
To set up your microphone ready for use plug it into the mic socket at the back of your PC, fig 1.1 shows a common set of sound inputs/outputs and we have pointed out the mic socket.

--------------------------------------------------------------------------------
The next step is to open the messenger program and contact the friend that you want to talk to, when you have sent them a message you will see the main instant message window, one of the icons visible is the voice button.
--------------------------------------------------------------------------------
Clicking on the voice button adds a new toolbar with some new areas of interest within the message window, these extra buttons/indicators (see fig 1.2) are what you will use to control the voice conferencing.

--------------------------------------------------------------------------------
Back to top | Part 5 coming in the next few days - © Copyright 2001-2008 helpwithpcs.com
--------------------------------------------------------------------------------
The Voice conferencing Toolbar

Above in fig 1.2 we have pointed out the main areas that are used to control the voice conferencing:

A - This is similar to the hands free feature on a normal telephone, allowing the user to talk without pressing the Talk button, when selected a certain volume triggers the hands free feature.

B - The Talk button is what you press and hold to speak, for better results this button should be pressed and held 1 second before you start to talk.

C - This is a level indicator, it indicates the input level of your microphone.

D - This is another level indicator, this one indicates the level of the incoming voice (your friend's voice).

E - The mute facility is much like the mute on your TV, when selected it mutes all sound.

F - This is a level indicator which indicates the level of the sound output.
--------------------------------------------------------------------------------
Back to top | Part 5 coming in the next few days - © Copyright 2001-2008 helpwithpcs.com
--------------------------------------------------------------------------------
Setting up the sound levels

Now you are familiar with the voice toolbar it is time to test and set up the sound levels including the input level for your microphone, this is achieved by opening the volume control on the Windows taskbar (bottom right of your screen by the clock).
In fig 1.3 to the left is a standard volume control window, yours may vary with different controls for different devices.

The one we are interested in is the Mic control, if you cannot see the mic in your volume window then click on options, properties, and then put a tick next to the Mic option in the dialogue box that appears.

Normally your mic will be muted so we need to untick the Mute checkbox (as in fig 1.2), now move the slider for the mic about halfway up for now, we will test the settings in a minute.

Also notice the Volume slider, this should be set according to your PC's speakers.

Now it is time to test the mic, when you enable the voice conferencing (clicking the Voice button) your friend will receive a message asking them if they would like to enable voice as well, presuming they do accept then you would see a message appear in the message window along the lines of your friend has enabled voice conference.

Press the Talk button and say something into your mic, you should see your mic level indicator (C in fig 1.2) light up, the ideal level is shown in fig 1.4 below

Having the mic any louder than the level shown above can cause distortion, adjust your mic slider (fig 1.3) to set the level accordingly, always ask your friend how it sounds at their end too.

Once you have set your levels you are ready to go, just press the talk button or use the hands free feature to talk.

To stop the voice conference simply click on the Voice Off button as seen below

note: If you experience feedback (a humming noise) while talking then adjust the volume and mic sliders until the humming disappears, another cause of feedback is having the mic too close to the speakers.

--------------------------------------------------------------------------------
Back to top | Part 5 coming in the next few days - © Copyright 2001-2008 helpwithpcs.com lintasberita

Processor

What is a processor and what does it do?

The processor (often called the CPU) is the brain of your PC and is where the majority of the work is performed.

As its name suggests a processor processes something, that something is data, this data is made up of 0's and 1's (zeroes and ones).

To understand a processor we first need to take a quick look at the way digital systems function. All of the work that goes on inside your PC is carried out by the means of voltage, or more accurately the difference in two voltages.

note: Voltage refers to the electrical unit. (for example a 12 Volt battery)

Digital systems use only two voltages, one which is a low voltage (usually between 0 and 1 volt) and one which is a high voltage (typically between 3 and 5 volts). These low and high voltages represent off and on respectively, a digital system will interpret these off and on states as 0 and 1. In other words if the voltage is low then it would represent 0 (off state), and if the voltage is high then it would represent a 1 (on state).
These zeroes and ones are called bits. The word bit is short for Binary Digit.
For example here are 8 bits (binary digits): 10010010
For more on binary see our guide to binary numbers.

back to top | © Copyright 2001-2008 helpwithpcs.com

Processor Architecture

A processor (as stated earlier) processes bits (binary digits) of data. In its simplest form, the processor will retrieve some data, perform some process on that data, and then store the result in either its own internal memory (cache) or the systems memory.

You may have seen processors advertised as 32-bit or 64-bit, this basically means that the processor can process internally either 32 bits or 64 bits of data at any one time.

This would theoretically make a 64-bit processor twice as fast as its 32-bit counterpart.

Software can also be defined as either 16-bit, 32-bit or 64-bit. You can probably see that theoretically, if you are using 64-bit software with a 32-bit processor then it would take two clock cycles (32-bits at a time) to process any one set of 64-bits, this is referred to as a bottleneck.

back to top | © Copyright 2001-2008 helpwithpcs.com

Processor Clock Speed

Every processor has its own built-in clock, this clock dictates how fast the processor can process the data (0's and 1's). You will see processors advertised as having a speed of say 2GHz, this measurement refers to the internal clock.

If a processor is advertised as having a speed of 2GHz, this means that it can process data internally 2 billion times a second (every clock cycle). If the processor is a 32-bit processor running at 2GHz then it can potentially process 32 bits of data simultaneously, 2 billion times a second !!

back to top | © Copyright 2001-2008 helpwithpcs.com

Front Side Bus (FSB)

Overall processor performance relies on other internal and external factors, one of which is the processor's front side bus (FSB) speed, two common figures for the Intel Pentium 4 are 533MHz and 800MHz.

The front side bus consists of two channels, one for transferring data, and one for indicating the memory address where the data is to be retrieved from or stored.

The front side bus transfers data between the processor and the computer's other components such as memory, hard drives, etc. The FSB will have a certain width (measured in bits) which dictates how many bits can be transferred at any one time. As the 533MHz and 800MHz figures suggest, the FSB also has a clock cycle frequency indicating how fast the data can be transferred.
For example a processor having a FSB width of 32-bits and running at 533MHz, can transfer a set of 32-bits of data, 533,000,000 times a second.

back to top | © Copyright 2001-2008 helpwithpcs.com

Instruction Sets

The type of work a processor carries out is defined by its instructions, these instructions are coded in binary. All modern processors have their own instructions built-in for common tasks.

Having these instruction sets built-in allow the processor to carry out certain operations much faster. The instruction sets that are built-in depend on the processor's architecture, there are two main types of processor architecture on the market, CISC and RISC.

CISC (Complex Instruction Set Computer)
CISC processors have more internal instructions than its RISC counterpart allowing a more diverse set of operations. Although this may sound the best option, CISC processors are generally slower due to the complexity of the instructions. Some people think the benefit of having more complex instructions built-in outweigh the performance lose, but it would depend on the applications that the processor is going to run.

RISC (Reduced Instruction Set Computer)
RISC processors, as the name suggests, have fewer built-in instructions, this can add to the overall speed of the processor due to the simplicity of the instructions, but again the performance would depend on the type of applications the processor was to be used for.

Most modern processors have built-in instructions specifically designed for certain applications such as 3D graphics, audio manipulation, etc. One example of this would be the MMX (MultiMedia eXtension) technology which Intel built-in to its Pentium architecture in the late nineties. This was a special set of internal instructions that allowed the faster processing of audio and visual algorithms.

back to top | © Copyright 2001-2008 helpwithpcs.com

Cache (L2)

L2 Cache (pronounced cash) is a special block of memory inside the processor (in the same chip) which offers faster data retrieval, typical sizes are 128KB, 256KB and 512KB.

note: Some processors (generally older) utilise external L2 cache.

The data that the processor stores in its cache memory will be data that is frequently used (such as a certain algorithm), the processor will also guess what data may be required and store this data in its cache. This guessing may be successful or it may not, the success rate is known as a hit rate. For instance, if the hit rate was 94% then it would mean that 94 out of every 100 attempts the processor correctly identified and stored a block of data which was needed, the other 6 times the data was never used.

back to top | © Copyright 2001-2008 helpwithpcs.com

Arithmetic Logic Unit (ALU)

The ALU is an internal part of the processor which is used for all mathematical and logical operations. The basic operations of an ALU include adding and multiplying binary values, as well as performing logical operations such as AND, OR and XOR. The algorithms for performing these mathematical and logical operations are hard coded (stored permanently) within the ALU.

back to top | © Copyright 2001-2008 helpwithpcs.com

Floating Point Unit (FPU)

The FPU is also an internal part of modern processors. The FPU is designed to handle any floating point calculations, and like the ALU it has its algorithms hard coded (stored permanently) inside the unit.

With the Intel family of processors up until the 80486DX the floating point unit was an external unit (commonly called a math coprocessor), subsequent processors such as the Pentium have the FPU built in. For example, if you had the (now old) 80386SX processor from Intel you would be able to purchase the 80387 coprocessor, which was in fact the floating point unit.

back to top | © Copyright 2001-2008 helpwithpcs.com lintasberita

Power Supply

What is a power supply and what does it do?
The power supply unit (PSU) in a PC regulates and delivers the power to the components in the case.
--------------------------------------------------------------------------------
Power Supplies contain dangerous voltages and should only be opened by experienced and qualified engineers, there are no user servicable parts inside.

Always disconnect the PSU from the mains supply before removing the cover of the PC.

--------------------------------------------------------------------------------
Standard power supplies turn the incoming 110V or 220V AC (Alternating Current) into various DC (Direct Current) voltages suitable for powering the computer's components.

Power supplies are quoted as having a certain power output specified in Watts, a standard power supply would typically be able to deliver around 350 Watts.

The more components (hard drives, CD/DVD drives, tape drives, ventilation fans, etc) you have in your PC the greater the power required from the power supply.


By using a PSU that delivers more power than required means it won't be running at full capacity, which can prolong life by reducing heat damage to the PSU's internal components during long periods of use.

Always replace a power supply with an equivalent or superior power output (Wattage).

There are 3 types of power supply in common use:
AT Power Supply - still in use in older PCs.
ATX Power Supply - commonly in use today.
ATX-2 Power Supply - recently new standard.
The voltages produced by AT/ATX/ATX-2 power supplies are:
+3.3 Volts DC (ATX/ATX-2)
+5 Volts DC (AT/ATX/ATX-2)
-5 Volts DC (AT/ATX/ATX-2)
+5 Volts DC Standby (ATX/ATX-2)
+12 Volts DC (AT/ATX/ATX-2)
-12 Volts DC (AT/ATX/ATX-2)
A power supply can be easily changed and are generally not expensive, so if one fails (which is far from uncommon) then replacement is usually the most economic solution.
--------------------------------------------------------------------------------
back to top | © Copyright 2001-2008 helpwithpcs.com
--------------------------------------------------------------------------------
The power supply connectors
4 Pin Berg Connector
Used to connect the PSU to small form factor devices, such as 3.5" floppy drives.
available in: AT, ATX & ATX-2
4 Pin Molex Connector
This is used to power various components, including hard drives and optical drives.
available in: AT, ATX & ATX-2
20 Pin Molex ATX Power Connector
This is used to power the motherboard in ATX systems.
available in: ATX( ATX-2 have four extra pins)
4 Pin Molex P4 12V Power Connector
Used specifically for Pentium 4 Processor Motherboards.
available in: ATX (integrated into the power connector in ATX-2)
6 Pin AUX Connector
Provides +5V DC, and two connections of +3.3V.
available in: ATX/ATX-2

--------------------------------------------------------------------------------
back to top | © Copyright 2001-2008 helpwithpcs.com
--------------------------------------------------------------------------------
ATX Power Supply Pinouts
Below are pinout diagrams of the common connectors in ATX power supplies.

note: The pinouts above relate to the connectors not the sockets.
note: To power up an ATX or ATX-2 PSU for testing, short pin 14 (PS_ON) with one of the grounds. lintasberita

RAID CONFIGURATION

RAID Levels, Data Striping, Disk Mirroring and Parity Fault Tolerance

RAID - Redundant Array of Independant Disks
RAID is a hard disk technology which can be used to speed up data transfer and/or provide disk redundancy.

RAID provides these features by utilising more than one hard disk at a time, there are several variations of a RAID configuration referred to as levels.

Each of these levels provide different performance and/or fault tolerance benefits.

© Copyright 2001-2008 helpwithpcs.com

Below are some RAID configurations with a brief description.

RAID 0
This configuration is the fastest of all the RAID levels, it uses a technique called data striping (see below) and requires at least 2 hard disks.

RAID 1
This level uses a pair of hard disks at a time to provide fault tolerance (there is no performance benefit) and requires at least 2 hard disks.

Using a technique called disk mirroring (see below) the same data is written to both disks at a time, so if one hard disk crashes then the same data is available from the remaining hard disk.

RAID 2
The RAID 2 configuration uses data striping (see below) and a fault tolerance technique called parity (see below), it requires at least 3 disks.

Two (or more) of the disks are used to store the data and one disk is used to store the parity (see below) information.

RAID 2 strips the data into bits, which is why RAID 3 (below) is a better implementation as it strips the data into bytes instead.


RAID 3
A common RAID level similar to RAID 2 except that the data is striped into bytes and not bits, giving a performance benefit over RAID 2.

RAID 4
RAID 4 strips the data into blocks and uses a parity drive for fault tolerance, at least 3 drives are required, not a commonly used implementation.

RAID 5
A popular RAID configuration utilising at least 3 drives.

Data is striped across the drives in bytes, the parity data for one particular drive is stored on another drive allowing the data to be rebuilt using the parity technique.

© Copyright 2001-2008 helpwithpcs.com

Data Striping
Data Striping is a technique for writing and reading data sequentially to/from more than one storage device.

Before the data is written it is broken up into blocks, these blocks vary in size depending on the RAID configuration (level) used.

The blocks of data are then written sequentially to all disks simultaneously into areas called stripes.

Because all of the read/write heads are working all the time, it increases performance as opposed to writing/retrieving data to/from one disk at a time.

© Copyright 2001-2008 helpwithpcs.com

Disk Mirroring and Disk Duplexing
This technique does exactly what it sounds like, it creates a mirror image of the information of one disk onto another.

The data is written to both disks at the same time, if one disk fails then the mirror disk can be utilised immediately to provide requested data and/or restore the lost data.

Disk Mirroring techniques usually use one disk controller for both drives. This can lead to problems, if for some reason the disk controller has a failure, then none of the disks would be available.

Disk Duplexing gets around this problem by using a separate controller for each data disk, allowing total disk redundancy.

© Copyright 2001-2008 helpwithpcs.com

Parity Fault Tolerance
This is a technique which is fairly simple but very effective.

It works by performing a logical operation on the data as it stores it and writing the result of this operation to either a dedicated disk (RAID 2,3 & 4) or on the main data disks (RAID 5).

The logical operation normally used is XOR (eXclusive OR).

An example, if there were 4 data disks in use called DD1, DD2, DD3 and DD4, and one parity disk PD1, whenever data is written to the drives the logical operation that would be performed is:

DD1 XOR DD2 XOR DD3 XOR DD4

and the result stored in PD1

Then if any of the drives fail the data can be rebuilt by performing a similar calculation, but this time substituting the missing data with the value of PD1.

For example, if we were missing DD2, the calculation would be:

DD1 XOR PD1 XOR DD3 XOR DD4 = DD2 (the missing data)

One of the drawbacks to using this type of fault tolerance is a speed loss due to the overhead of the calculations, it obviously needs to use up some disk space too, but it can be invaluable when it comes to retrieving otherwise lost data.

© Copyright 2001-2008 helpwithpcs.com lintasberita